PDA

View Full Version : SILLY QUESTIONS FROM NEWBIES!


  1. Floating Tubing ?
  2. Aluminum End-cap Heatsink, for SD
  3. Fittings Kit for type VII
  4. Type VII S/D instructions for very newbie's
  5. WFLY 6 channel receiver won't fit in type VII S/D
  6. lipo charger supplied with Caswell order
  7. Water proof toggle switch
  8. battery question
  9. making up the snort and mpc
  10. Aerial on S/D
  11. Battery for the Seaview
  12. RVG004 - 5 disc gato build set
  13. Plastic cleaner
  14. Bubbles from blow hole.
  15. Template for flood vents
  16. backordered S/D
  17. Sd2vii
  18. Tube size clarification for Snort System
  19. servos slip on rail?
  20. Really Dumb question.
  21. Kilo hatch
  22. Forward dive plane mechanics?
  23. Motor stopped working on type-7 S/D
  24. snort fittings
  25. Can't upload photos to my album now
  26. 1/72 Gato Snort pump size? Nautilus WTC?
  27. motor shaft couplers
  28. Motor stopped working on port side again!!
  29. My U-552 travel box
  30. akula help
  31. Seawolf fittings kit goes where
  32. How many radio channels for Subdrivers
  33. gato single motor question
  34. Fittings for Gato
  35. 8 channel radio
  36. stop the lean
  37. Where to fit everything?
  38. How do you see it when it's underwater?
  39. Clear plastic parts
  40. Joining hull halves
  41. Air tank and compressor
  42. Seaview Motor Shafts Question
  43. Third servo
  44. Servos up front?
  45. more power
  46. Servo jitter
  47. Charging Batteries & Power Toggle Switches
  48. Gato Decals
  49. AHHH
  50. Type VII SD question
  51. Silly question from a noob
  52. Subdriver Setup
  53. Ballast System Query
  54. all is well
  55. dive plane setup question
  56. setting up props and shafts
  57. new to subs
  58. two stupic questions about props and motors
  59. Propeller Efficiency
  60. 54" Tote Box
  61. how to mount a deck
  62. very new to this
  63. sea trials today good and bad
  64. how long should it take to flood a 3.5 wtc
  65. Dragon Shark 1/72 Sub
  66. Radios
  67. Revell 1:72 VII U-Boat
  68. When Does One Qualify for Dolphins
  69. U Boat type VII/C Dive Plane Configuration
  70. Hi everybody!
  71. Radio frequencies
  72. balsa sub
  73. Vent holes
  74. Two Questions in one Post!
  75. Heat Buildup
  76. Hello i'm new.
  77. Choice of paints
  78. Want to get it right!
  79. Adheasive used for gluing "Foam" to inside of gato?
  80. Three Servos moving All at Once?
  81. Stand Alone Sub-driver.
  82. Snort Installation of hose into ballast tank and does it need a Check Valve?
  83. Anodize?
  84. Receiver antenna
  85. Air pump questions
  86. Gas/RCABS Hybrid
  87. question on the u-99 model
  88. sub 10 esc
  89. txmitter/rxers
  90. question bout sub 10 wire
  91. Where to run?
  92. K Class submarine
  93. Peristaltic pump
  94. Fixing gouges
  95. Difference Revell Gato 5047 and 850(384)
  96. Temporary glue
  97. Mixed Radio-Acoustic Link for Control/Communications
  98. Moebius Seaview instruction sheet
  99. What's a good source for a radio?
  100. chasing a leak
  101. Thinking outside of the box - two receivers
  102. building materials
  103. Opening limber holes
  104. motor problems with 3.5 wtc 2 motor drive
  105. Up Periscope and the Seaview
  106. Cleaning up Sculpey
  107. Molds for vacu-forming
  108. Replacing the Up Periscope lens
  109. Installing Klik-ons
  110. Fiberglass layup Respirators?
  111. Air Questions
  112. Revell Skipjack Subdriver instructions
  113. Switch for channel six
  114. D&E Sub-driver 3.0 Not supported anymore?
  115. Snorts and external ballast tanks
  116. Additional Switch
  117. Allen screwdriver
  118. Snort system?
  119. Low cost Digital Video Recorder
  120. newbie silly question... maintence.. pushrods...
  121. re revell xx1 sub 1/144 plastic kit
  122. wfly 6 channel transmitter crystals?
  123. Newbie, Building Gato or Trumpeter Kilo, whats involved?